home *** CD-ROM | disk | FTP | other *** search
/ The X-Philes (2nd Revision) / The X-Philes Number 1 (1995).iso / xphiles / hp48_2 / open48.how < prev    next >
Internet Message Format  |  1992-08-05  |  9KB

  1. From comp.sys.hp48 Wed Aug  5 22:54:49 1992
  2. Path: seq!rock!stanford.edu!rutgers!usc!sdd.hp.com!hp-cv!hp-pcd!hpcvra!rnews!hpcvbbs!akcs.n2kyw
  3. From: akcs.n2kyw@hpcvbbs.cv.hp.com (Paul Smith)
  4. Newsgroups: comp.sys.hp48
  5. Subject: How to open your hp48
  6. Keywords: passkey keyboard rclkeys stokeys hokey smokey
  7. Message-ID: <2a730720.1487comp.sys.hp48@hpcvbbs.cv.hp.com>
  8. Date: 26 Jul 92 20:40:02 GMT
  9. Lines: 171
  10.  
  11. Disassembling the hp48sx 
  12. (may or may not correspond to the 48s, but probably will to some 
  13. extent)
  14.  
  15. Sufficient numbers of people (more than 1) have requested information 
  16. on how to disassemble their hp48.  Despite the fact that that's pretty 
  17. scary, I will entail what I know here.  Thanks to David Holmes for 
  18. taking the first step and helping make my attempt more informed.
  19.  
  20. None of the information that follows came from hp, so if what I say 
  21. starts to sound rather official, it's not.
  22.  
  23. For the few folks out there who've actually had to send their hp48 
  24. back to hp for service, you probably ended up with an entirely new 
  25. unit.  I suspect the reason for this, aside from some labor cost 
  26. savings on the part of hp, is that they really aren't much fun to take 
  27. apart.  You can draw your own conclusions as to why it was designed 
  28. that way.
  29.  
  30. 0.  Backup your memory.  You will need to remove the batteries for 
  31. awhile to disassemble the unit, and you may have them out long enough 
  32. to cause memory loss (although in my case, even 2 days didn't wipe 
  33. anything out).
  34.  
  35. 1.  Remove the tin key overlay.  The overlay is attached with double-
  36. sided tape of some sort.  A little care and patience will allow you to 
  37. remove it only slightly warped, and it is fairly easy to straighten 
  38. out later.  I took a small jewelers screwdriver and started prying 
  39. near the "ON" button, and worked upward toward the screen.  When you 
  40. get near the screen, try to preserve the shape of the overlay because 
  41. that portion is a bit more difficult to properly straighten later.  
  42. Once the overlay is removed, put it in a container or somewhere away 
  43. from dust.  The double-sided tape should stay with the overlay (mine 
  44. did, at least) and will gather dust and stuff making it less sticky if 
  45. left out in the open.  48sx owners will need to remove the little hp 
  46. logo insert above the screen as well.
  47.  
  48. 2.  Defeat the 10 plastic rivets.  Believe it or not, these rivets 
  49. aren't all that critical to holding the unit together, so you can be 
  50. as careful or as reckless as you want (I prefer reckless, because I 
  51. hate plastic rivets).  A good way to carefully remove the rivet heads 
  52. is to use a flat head screwdriver that is the same width as the 
  53. recessed rivet hole (4mm?) and "drill" the head away by hand with the 
  54. screwdriver.  The head is about 2mm deep, so stop "drilling" there to 
  55. leave the keyboard material shoulder intact for easier reconnection 
  56. later.  There are 6 rivets near the number keys and four above the 
  57. screen.  These rivets above the screen perform more of a holding 
  58. function than the others, and you may want to consider using some 
  59. screws and small washers to replace them when you re-assemble.
  60.  
  61. 3.  Separate the lower half from the upper half.  The upper half of 
  62. the calculator contains almost all of the components except for the 
  63. piezo "beeper" element, and there are no interconnecting wires between 
  64. halves.  The only obstacle is the snap-together "hooks" that David 
  65. Holmes refers to. These hooks are positioned near the [A], [F], [SIN], 
  66. [1/x], [ON], [+] and [.] keys (the one by the [.] key is a real 
  67. bugger!).  Refer to the cutaway diagram below for details.
  68.  
  69.  
  70.  
  71.  
  72. Key overlay here ___
  73.                     \     ____________
  74.                      \   |            |
  75.              ____________|    ______  |
  76.                              |   _  | |  <--- Upper section.
  77.                              |  | | | |
  78.              ________________|  | | |_|
  79.                              |  | |___  
  80.   Circuit board and other    |  |     |
  81.   components (affixed to     | /      |  <--- Lower section.
  82.   upper section)             |/__     |        Has a lip which 
  83.                              |   |    |        engages with metal 
  84.            Metal "hook" ---> | / |    |        "hook" from upper 
  85.                              |/  |    |        section.
  86.                              |   |    |
  87.              ________________|   |    |
  88.                                  |    |
  89.  
  90.  
  91. To separate the two sections, you will need to push the lower section 
  92. out and down around the hooks.  You can't do this from the outside 
  93. because the upper section hangs over the lower, so you have to go from 
  94. the inside.  Luckily, the six slots in the keyboard (used by the 
  95. separate user-overlays that fit over the original overlay) near the 
  96. [MTH], [ENTER], [blushift], [NXT], [backspace] and [-], come in handy 
  97. for this.  These slots are not exactly lined up with the hooks, but 
  98. are close enough.  You can insert something in these holes (I used a 
  99. jewelers screwdriver, flat head) at an angle that is mostly down and 
  100. somewhat out, to a depth of about 5mm, and come in contact with the 
  101. lower section.  Push the lower section out about 2mm (this will take a 
  102. bit of force), while wedging something in the outside gap to separate 
  103. and hold the sections apart while working on the other hook positions ( 
  104. a wooden matchstick works).  I recommend starting with the [A] or [F] 
  105. positions first, working down whichever side you started with, then do 
  106. the other side, and leave the [.] position for later (there is no 
  107. helpful slot there).
  108.  
  109. 4.  Remove the battery cover and the batteries.  The two battery 
  110. contacts which come through the case will need to go back through the 
  111. case when the sections separate.  The upper contact is hooked on a 
  112. plastic boss, and needs to be freed from it.  Just pop it off with 
  113. your finger or a screwdriver.
  114.  
  115. 5.  Very carefully pull the two sections apart at the top (above the 
  116. screen).  If you have freed all the hooks, the case should sort of 
  117. hinge at the bottom edge.  This is due to the last hook (near the [.] 
  118. key).  Some careful twisting and working of the sections should free 
  119. this hook as well. You should now be able to completely separate the 
  120. two sections.  I recommend at this point that you take a pair of 
  121. pliers and flatten that last hook so that it will not hold next time.  
  122. It is really not needed anyway, as the other six hooks hold the unit 
  123. together just fine.
  124.  
  125.  
  126. Now you can poke around and explore things.  Be careful what you 
  127. touch, I'm not sure how sensitive the insides are to static discharge 
  128. from your fingers, etc.  If you're interested in adding stuff, some 
  129. open real estate can be found in the areas between the battery 
  130. compartment and the card receivers, and in the cavities in the lower 
  131. section below the tin shielding on either side of the card ports (this 
  132. is where I put some jacks).  If you own a 48s, you may find a lot more 
  133. space.
  134.  
  135. If you want to disassemble the unit further, like removing the circuit 
  136. board from the upper section, you have a considerably tougher job on 
  137. your hands, and you're on your own.  Also, if you separate the screen 
  138. from it's circuit board, you will disturb the rubber conductors (there 
  139. are two) which provide electrical connection to the lcd rows and 
  140. columns (zebra strips).  Upon reassembly of the screen, you may find 
  141. that you have lost some rows or columns in the display (not permanent, 
  142. just a zebra strip alignment problem) and will have to keep 
  143. reassembling and perhaps cleaning until it comes out okay.  I haven't 
  144. done this to my hp (yet) but I have done it to other cheap calculators 
  145. and it wasn't fun.
  146.  
  147. As to questions about what exactly is inside, I can only guess.  David 
  148. Holmes had some observations, and there are apparently a lot of people 
  149. out there in netland that know a lot more about the insides already.
  150.  
  151.  
  152. Reassembly-
  153.  
  154. Putting it back together is much easier.  You may need to clean up the 
  155. remains of the rivet heads so they will easily reinsert into their 
  156. holes.  Make sure the battery connections align with their respective 
  157. holes, and snap the unit together, applying pressure where the six (or 
  158. seven, if you left that one near the [.] key alone) hooks are.  You 
  159. will probably want to hold the case together at the top with one or 
  160. two of the rivets there.  If you can find a wood screw with a flat or 
  161. thin head, you can screw it into the body of the rivet and let the 
  162. head hold the upper section surface.  You may need a small washer for 
  163. this.  A machine screw will probably work as well, but will strip the 
  164. plastic easier and not hold as well.  I have only one screw holding 
  165. mine together and it works fine.
  166.  
  167. You will probably need to re-shape your tin overlay, as it probably 
  168. took a beating during removal.  I removed the sticky tape from mine, 
  169. but it's probably better not to (unless it really wont stick anymore).  
  170. Put wax paper over the tape and put the overlay face down on a hard 
  171. cover book.  Grab a hammer with a smooth and somewhat flat head, and 
  172. pound away.  DONT pound away on the part that surrounds the screen 
  173. (beveled part).  You can probably use your fingers and a little 
  174. massaging to fix that area.  With a little care you can end up with an 
  175. overlay that looks like new.  Press the overlay in place and hope it 
  176. sticks.  If not, a little rubber cement wouldn't hurt.
  177.  
  178.  
  179. Have fun!
  180.  
  181. Paul Smith
  182. v055qmd6@ubvms.cc.buffalo.edu
  183.  
  184.